The Jalopy Journal
These two carbs were used on the intake but have sat for years and looks like they were kind of rigged to begin with. I'd like to rebuild both...
Hi all!! I recently noticed on my 1961 Chevy Apache that it has got a “miss” feeling at cruise speeds. So I decided to do a leak down test and it...
1959 Chevrolet Apache Fleetside Project 1/2 Ton, Longbed, fleetside This truck was a barn find, the only item that was missing when found was the...
Hey Hambers, I'll try my best to describe what i'm trying to achieve. Car/Engine: 235 Chev: Has any one installed an Electric Fuel Pump, But...
I'm in the process of acquiring a 1946 Chevrolet Truck from a friend of mine that has been kept in a shed... no rust, very few dents, all panels...
Hi all, Not sure if I'm in the right forum for this but everyone here seems to be helpful anyway so here goes. This afternoon I noticed the...
I have a 1950 Chevy convertible all original with stock 216, 3spd, 6 volt, and 3.55 rear closed torque tube. I have a line on a 53 Chevy 235 with...
Hey Y'all! I live in S.C. I have been working on airplanes and cars since I was a kid. I helped my dad in his airplane shop. Then after a...
I've been fiddling with my daughter's 57 chevy with a 235 and if it sits for a day or two it's super hard to start - The old Rochester B that was...
I got a 55 Chevy truck second series with a 235. Im looking at getting a pair of split headers and dual intake. Of course, I'm looking at Fenton...
1952 GMC 3/4 Ton. This truck is solid. Only two rust holes and they are both only about the size of a quarter. Solid Arizona truck that I have...
I have a 235 in my 59 Apache that is making noise (probably wrist pin) and is casting # 2764476. I have a replacement 235 of same time period that...
selling a great running 235 stovebolt six banger. has around 59,000 miles on it, removed from a 57 chevy 210. does not come with a carburetor but...
Hello Again Hamb'ers! So I've got to ask this question before the wife gets home and we do our Valentine's Day song and dance. I installed an...
Hey everyone, new guy here. Recently picked up a 53 gmc 9300 from my uncle. Trucks been in my family it's whole life but had seen better days so...
I am in need of some assistance. I purchased a used 1960 235 truck motor with a rebuilt head. Compression test ranged from 135 -140 between the 6...
Runs great includes freshly rebuilt updraft carburetor.
Very nice solid Montana Truck. It is a 3600 with a 235 that runs good doesn't smoke but will need serviced to be put on the road. I got it...
Yes, rare vintage Edmunds Custom Chevrolet Intake for 216/235 6 cylinders. Comes with dual carter YF carbs. Carbs aren't stuck. Will need to be...
[ATTACH] [ATTACH] [ATTACH] 51-52 Chevy radio delete. Perfect condition. Little surface rust on backside.no bondo under basecoat clearcoat. Perfect...
Chevy blue flame 235 with trans. Motor turns free. Trans gear looks great
hey guys! So A few of us are trying to help a friend out with his motor swap. 1949 Chevy fleetline. Pulled the 216 and three speed and we are...
This engine is already sold and no longer available I have a 1954 235 L6 that came out of a 54 Chevy Pickup. The motor was running when I...
Just recently pulled from my 1953 Chevrolet Bel Air with 40,000 original miles on it, this 235 straight 6 ran great with no issues. No knocking,...
SOLD
[ATTACH] [ATTACH] Vintage edelbrock dual carb intake manifold with linkage....no carbs These are getting hard to come by. 250.00 Fits 216...
Hi gearheads, I want to get rid of the road draft tube located at the bottom of the 235 engine. I read an article of someone who installed a...
Hi gearheads, I want to pull the 235 engine (for rebuilding purposes) from my '54 Chevy handyman WITHOUT pulling the tranny . I removed the brace...
Could anyone that has done the T5 swap onto a GM 235ci post pictures of how they rigged their slave cylinder setup? I just did the swap, went...
Separate names with a comma.
The Jalopy Journal
