The Jalopy Journal
Hey guys, Me and my brothers ‘49 had just gotten light driving this year. We got it running again (thanks to you all helping me with electrical...
I have a ‘49 8CM with Edelbrock heads. The plugs I pulled out were Autolite 216 “Shorties” approximately .500” from washer to top of strap. The...
THEY NO LONGER MAKE THESE FOR FLATHEAD FORD. Bellhousing to adapt a Ford Flathead 1949-1953 to Chevy T5 transmissions. Bellhousing mocked up but...
Mallory Unilite distributor for Flathead ford. $250 plus shipping. Also available for pick up in Orange, CA
SOLD SOLD SOLD Turn key 1936 Ford Pickup. Extremely clean and original, restored about 20 years ago and has spent most of its life parked in the...
Old polished 3x2 intake. Small repair on center carb flange(will require an insert to tread stud into). Missing a couple of studs. Comes with...
Trans came out of a '53 Ford pickup. Has Borg Warner R10 overdrive. Spins freely and shifts into all gears. Comes with bellhousing and starter...
Hi all, Looking for some advice from the hive mind. I've been presented with the opportunity to buy a pair of Stromberg BIG97's at a very good...
8BA engine with Offenhauser heads, 4” merc crank, .80 over pistons, adjustable lifters. I also have other intakes if you aren’t interested in the...
Hi! Ok, embarrassing. Was troubleshooting my wiring Sunday and after not finding the problem I accidentally left the ignition on :( burned up the...
Up for sale is my 1940 ford deluxe Tudor Sedan. It's running a 49 8ba 239 flathead with dual stromberg 97 carbs sitting on a Fenton dual intake....
Hey guys, Hope all are doing well. I'm trying to install an alternator in my 40 ford. It's a 12v system and am running an 8ba. I'm curious if...
Good evening Everyone! I wanted to hop on here and ask for a bit of advice. To start off, I have a 1940 Ford Tudor Sedan, rebuilt 59AB, punched...
I wanted to create a post to make a sort of "how to" for removing stubborn valve assemblies. I realize there are more stubborn engines than mine...
Hello, I'm not too pleased with my flathead. I want something a little more stout, and something a little more cost effective. Parts cost way too...
[ATTACH] I'm a Nailhead Guy and new to the Flathead scene. The fan on my 8BA is loose and causing one heck of a vibration. From what I...
Fenton Aluminum Heads Ford flathead V8 1949-1953 8BA Local pick up 47905 Or Buyer pays shipping
The other day I was driving when suddenly I felt one hell of a vibration. Got out and the crank pulley on my '49 Merc. 8BA had come loose. Was...
Here are some Eddie Meyer Hollywood speed equipment shift knobs, there are 3 different logos to choose from, the knobs are black bakelite , 2" in...
Hey everyone I could use some wisdom here. I have an 8BA with an isky 400jr cam, thickstun pm7 intake and two fully rebuilt stromberg 97’s and the...
This is a brand new Ford flathead aluminum intake manifold and 8BA carb. Completely rebuilt carb. Never installed. Bolt on and enjoy! $150
Sold
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] I have a mallory dual points distributor for an 8BA flathead. I bought it and never used it ended up...
Both of them for $20 plus shipping. [ATTACH][ATTACH][ATTACH][ATTACH][ATTACH]
So I went to install my 59A heads onto my 8BA today and noticed the valve pocket in the 59A head is shaped completely different from the 8BA head....
[ATTACH] I have this flathead generator I’m trying to figure out the year? I’d like to remove the pulley and have it machined to fit my 8BA...
BUILT VERY TRADITIONAL The car runs great! Stops as it should and steers well for its age. I have consistently driven the car 55-65mph with NO...
Nice set of 8BA exhaust manifolds as pictured. $100 plus shipping. [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]
SOLD!! Up for sale is a brand new pair of aluminum Offenhauser heads for an 8ba flathead Ford. These are part number 1069 and retail for...
SOLD!!
Separate names with a comma.
The Jalopy Journal
