The Jalopy Journal
I have been doing some research here on the HAMB and I would like to swap to a lasalle 3 speed on my 394 engine in my '64 Super 88. However, I'm...
I was wondering if the 394 Oldsmobile rocker assemblies had (retainer?) springs and end caps that held the rocker arms in place when the engine is...
WHAT'S UP, Im new to the site, but have been lurking for months you could say. A little about me, Im a little green around the ears due to...
Hey there everyone! I am a newbie from Chicago il. I picked myself up a pretty nice 1950 plymouth special deluxe. I am having an issue with...
I have a holley 12-802-1 fuel pump located inside engine compartment on fender well. I ran it out of gas and it has not been the same fuel strav...
I am working on a 1950 ford 6 volt pos. ground. Ian trying to sort out how to wire a relay that I bought from newark element. It has five lugs on...
So ever since I bought my 51, it always had a very noticeable ticking sound that ONLY came when it came up to operating temperature. Im fairly...
First post...new to the HAMB So this has been an ongoing problem. I am running a carter p4070 electric about a quater of the way away from the...
Hello everyone longtime reader first time poster. I am currently completely rewiring my 53 Plymouth (aka Agnes) and I am running into a bit of an...
[ATTACH][ATTACH][ATTACH][ATTACH][ATTACH][ATTACH][ATTACH] I'm trying to identify two parts, a cowl vent and a pair of body panels. Note spring on...
Looking for a frame to put my 1922 franklin on I need a frame with a 116" wheel base and 32" wide any one know what might work for my project
hey guys! So A few of us are trying to help a friend out with his motor swap. 1949 Chevy fleetline. Pulled the 216 and three speed and we are...
Hey, has 72 FMX transmission and we are having a hard time figuring out what's wrong with it. Does anyone know what the line pressures should be?
I recently purchased a 1958 Ford thunderbird. Well, almost 2 years ago. Ive been working on it all the time that I might get between work &...
[ATTACH] [ATTACH] Hello all. I'm 22 years old from Maryland. Back story I bought a 66 f100 about 3 years ago. This truck started off as a...
Need some help please!!!! Running into issues with my SBF & AOD swap in my 1964 F100. Major issues right now are header clearance on the steering...
[ATTACH] Help !!! I am in search of a proper replacement fuel pump. The car is a canadian built Pontiac Laurentian 2 dr. sport coupe. 239...
I am looking for the backing plates so I can put an E-Brake on a car that is missing it. I need full size GM car axel I believe 72 to 77. All I...
I have a stock SBC 350, nothing is oversized, just plain ol' stock. It does have an Edlebrock preformance intake, every thing else is STOCK, what...
does any body have measurements of 29 roadster P/U body? the bottom dimensions and the top width and length measurement from dash to rear of cab...
Hello everyone my at has been sitting for about 8 weeks (been busy with work and school) when I parked my car my motor was running perfect and...
Hey guys, I need some help with my brakes... When I hit the brakes, the car locks what seems to be the drivers wheel with any brake pressure...
Today I broke the latch that keeps the door closed on my drivers door. I'm having a hard time finding a replacement online. I was wondering if...
Hey Folks, I've been going through the cooling system on the '51 and tonight when replacing the thermostat housings and thermostats, I broke off a...
Hello, I'm looking to get back into an American (less disaster prone) ride as a daily/ general work crummy. Leaning toward late 50's to...
Hey all. Just renewed my Alliance membership after bitching to myself about the snafoo of the speeds on the site. I finally figured out that it...
I cant seem to figure out what to do with the pipe that comes from the back top of the block and leads down next to the oil filter. I have the...
This weekend I am preparing to pull the motor and tranny as one out of my 49 sedan. I had a few questions about the process. maybe a walk through...
Hey guys, i already had a thread started about doing a swap in my 64' galaxie but it was to a 300 i6 which didn't work out because of the 300's...
I'm at my wits end with this thing. I have Chevy 350 trans that will not stop leaking. I first replaced the gasket with a cheap rubber one ( I...
Separate names with a comma.
The Jalopy Journal
