The Jalopy Journal
Nice clean set , no tubes or wire covers.
Very nice factory dizzy. Came from a 276 ci.
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] 1931 Ford Roadster. Sitting on Model A frame with rear frame height kick up and...
Hi Everyone, New guy here! I am adapting a 1953 331 Hemi to a Mopar/GM A833 4 speed. It's the one GM used in the light trucks from about 81/85ish?...
[ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] Super clean Cadillac 331 hot rod motor. Has good compression and...
Pro built '23 T: Powered by a '55 342 cu. in. Chrysler Hemi with a 6-71 blower, backed by a GM 4- speed trans and a 4:30 Ford 9" rear end. Starts...
Has a Hot Heads water pump kit, Chevy transmission adapter, headers and oil filter adapter. Have removed oil pan for inspection, very clean...
Very clean and very nice. Buyer pays shipping.[ATTACH] [ATTACH]
PAW #5751 AFB 4bbl Intake top for 354-392 Hemi. Never used. PAW went out of business in 2016. These retailed for $450 back then. Box has moisture...
I decided to go with fuel injection, so I am selling my Weiand #7263 2x4 aluminum intake. Comes with a matched set of Carter AFB carbs re-built by...
I'm working on the venting for my hemi. Its probably under 450 hp with dual quads. I have the PCV valve setup. My question is: How much...
29 ford roadster. Brookville body. 32 ford frame with original k member. Halibrand 201 qc. 331 hemi 4x2. 36 ford dash. 39 ford trans. Halibrand...
I need to replace the rear main seal. Any advice on rope or neoprene? Also any tricks or tips? The motor is a complete running motor. I can...
@Flogknaw has started threads about small blocks, big blocks, and the hemi. So i thought what about a picture thread for the most traditional hot...
241cu.in., "seasoned" block, .080 over, caps and rods. Caps from diff. engine. Will need to be line bored. $200.00 obo. Also and separate,. set...
Beautiful Edelbrock RR-1 426 HEMI Dual Quad Intake Manifold. 999.99, or best offer, plus shipping. Email wmp990@lindenwood.edu if you have any...
We have run across this jewel while buying another Dodge truck. This is a 1946 Dodge model WFA-32. I have been in the classic vehicles market for...
We pulled this running engine and transmission out of a 1940 Ford coupe. We don’t know a lot about the internals but removing the valve cover...
From a KD500 engine. If interested email and I can send a picture. I have three 315/325 engines that I have extra parts from. Let me know what...
Hi All I'm in the process of building a 354 Hemi with a Potvin setup for the street. I'm looking for anybody that has ACTUALLY BUILT an early Hemi...
1954 Chrysler 331 Hemi (Standard bell housing, not the extended version) Bored 0.030" Crank turned 0.010"/0.010" Rods resized, ARP bolts...
Complete set to adapt a short bellhousing 1955-58 Chrysler hemi to a GM hydramatic transmission. Includes the CRAGAR #407 adpater, crankshaft hub...
I had always guessed it was Ed Donovan himself. Then I learned that Mr. Donovan had worked with the great Leo Goossen at Offenhauser/Meyer &...
1954 Chrysler 331 cubic inch Hemi .030" bore, displacement is now 336" 8.5:1 cast pistons New bearings, rings, pins, valve job, Iskenderian cam,...
Two cams,... one stock, one Harmon & Collins steel billet. Both long nose for low deck 241/270 Dodge Red Ram Hemi or Poly. Figure shipping on...
[ATTACH] [ATTACH] Here is a 1955 Dodge Red Ram Hemi Crankshaft that has been machined and is ready for install. This fits the 241 cubic inch and...
Hello all, I have an odd ball situation. I'm trying to determine the best Carter WCFB for my car. Long story short, my car is a 58 Dodge Coronet...
A few questions for the early hemi/ stick racers... RAM or McLeod? (Want a slipper type clutch) Steel or aluminum flywheel?(blown 331 with mini...
[ATTACH] I’m am selling my Firedome. She was running but it’s been a bit, been garaged. The 276 hemi is original. Lots of work already done. I got...
Early Hemi 392 Mohawk starter adapter plate for the 1957 Desoto, Dodge, or Chrystler. Casting # 1736183. It is in good shape and has been media...
Separate names with a comma.
The Jalopy Journal
