Register now to get rid of these ads!

Need a rear axle measuerment

Discussion in 'The Hokey Ass Message Board' started by Pist-n-Broke, Feb 11, 2005.

  1. I need a total width measuerment axle flandge to axle flandge on a stock 55-56-57 Chev car axle. Can anyone help me out?
    The Wizzard
     
  2. Upchuck
    Joined: Mar 19, 2004
    Posts: 1,576

    Upchuck
    Member
    from Canada BC

  3. Brandy
    Joined: Dec 23, 2004
    Posts: 5,286

    Brandy
    Member
    from Texas

  4. Upchuck;
    This is what I love about the H.A.M.B. Ask And you shall recieve. Kool site and had all I needed. It told me I was looking for the wrong animal. In fact it looks like one doesn't exist.
    Brandy;
    No need to go outside to measuer your rear end. I'll just visualize it being the perfect one.
    Thanks again, The Wizzard
     
  5. Very close to 61" wide
     
  6. HELLBILLY
    Joined: Feb 9, 2003
    Posts: 682

    HELLBILLY
    Member

    [size=+1]MEASURED ACROSS WHEEL MOUNTING SURFACE[/size]

    56 1/2" 71-77 Ford Maverick 8",



    57" 71-74 V-8 Mavericks 8", All '75-77 6's & 8's Maverick 5 Lug 8", 49-51 Ford, 57-59 Ford 9"

    57 1/4" 64 1/2 - 65 Mustang

    58" 78-88 Mid sized GM Car, Malibu/Monte Carlo (82 up Metric Studs), 80 Granada & Lincoln Versailles,
    67-70 Mustang/Cougar/Fairlane, Regal with 10 bolt axle, S-10 P.U., 65-67 Nova

    58 1/2 " Ford Grenada

    59" 68-83 Corvette

    60" 55-64 Chevy Car, 67-69 Camaro, 64-67 Chevelle, 68-74 Nova, 71-73 Mustang/Cougar, 84-95 Corvette

    60-61" 64-69 1/2 ton 2wd Chevy/ Some GMC 6 lug rear end 12 bolt Coil spring set up Possible gear ratio's 3.70

    62" 64-77 Chevelle, 73-76 Torino, 89 Trans Am,

    70 2wd 6 lug rear end 12 bolt Possible gear ratio's 3:08, 3:40, 3:73
    70-81 4wd 6 lug reared ...............................................................

    71- Newer 2wd trucks use a 5 on 5 lug pattern
    71-76 Full Size Cars " "" "" " 60" 60's GMC and some Chevy's Dana 44 or Dana 60 with leaf springs 6 lug, Gear ratio's 3.21 to 3.92. GMC V-6 used a 3.21 Dana 44 used a standard chevy 1310 yoke, Dana 60 used the heavy duty yoke which takes the larger 1350 yoke.
     
  7. HELLBILLY
    Joined: Feb 9, 2003
    Posts: 682

    HELLBILLY
    Member

    [size=+1]Approximate rear end widths measured from backing plate to backing plate.[/size]Add Width to compensate for drums as follows: 4" - 5" for small cars 5" - 6" for intermediate cars 6" - 8" for large cars48" - 49" 50" - 51" 52" - 53"'71 Colt
    '72 Cricket
    '72-75 Datsun Pickup
    '72-73 Mazda '65 Ram American
    '74 Valiant '28-40 Ford , '57 - 59 Ford
    '62 Buick Skylark, '67 Chevrolet Six
    '67 Mustang Six , '68 AMX
    '69 Javelin Six , '70 dodge
    '70 Duster , '71-77 Maverick
    '71 Comet , '71- 72 Pinto 54" -55"56" -57"58" - 59"'39 -48 Chevrolet, '68 GTO
    '41 -48 Ford, '68-72 Chevelle
    '55 -57 Chevrolet, 68-69 Fair lane 6 or 8
    '66 Falcon, '69 Chevrolet
    '67 Mustang V-8, '69 Firebird
    '69 Cougar, '71 -73 Nova
    '73 Ventura, '73 Mustang'36 Plymouth, '54-56 Ford Pickup
    '67 Lincoln, '69 Dodge
    '69 Dodge Van, '71 Torino
    '72 Cougar, '74 Pontiac'49 Plymouth, '61 Chevrolet Impala
    '65 Cadillac, '66 Buick Wildcat
    '66-67 Chevrolet Big Car, '72 Charger
    '69 Oldsmobile 88, '72 Chrysler
    '72-73 Torino
     
  8. HELLBILLY
    Joined: Feb 9, 2003
    Posts: 682

    HELLBILLY
    Member

    I asked the same question once before and someone posted the lists above for me so I'm returning the favor for anybody else that can use them.
    Good folks here on the HAMB with a lot of great info!
    Thanks!:)
     
  9. Brandy
    Joined: Dec 23, 2004
    Posts: 5,286

    Brandy
    Member
    from Texas


    Cheeky monkey!:D ElPo---that 61 inches better not be a guesstimate of MY rearend!!! Oi!!

    x
    Brandy
     

Share This Page

Register now to get rid of these ads!

Archive

Copyright © 1995-2021 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.