Register now to get rid of these ads!

Pooch's 55 chevy build

Discussion in 'The Hokey Ass Message Board' started by Pooch, Aug 23, 2007.

  1. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma

    Okay... Okay.... stop begging here are the last four months of my life for your viewing pleasure. Starting with mockup pics.
     

    Attached Files:

  2. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma

    Two engine stands and a little black paint sure made the frame look like somthing that should be under a 55 chevy.
     

    Attached Files:

  3. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma

    Tuned the engine on the stand and droped it in the ch***is. The old guy in the pics is my dad. He put the ch***is together in about a week. I think he has had more fun building my car than I have.
     

    Attached Files:

  4. gnarlytyler
    Joined: Feb 2, 2007
    Posts: 1,004

    gnarlytyler
    Member

    Awesome :) :)
    -Anthony
     
  5. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma

    Thanks. It just gets better from here. Now we get some color and the two pieces get together for the last time.
     

    Attached Files:

  6. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma

    Headers, winshield, wheels, tires, fenders and trunk lid. Its starting to look like a car.
     

    Attached Files:

  7. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma

    Two days to Mokan and I got a lot done today. Alignment, front tires, exhaust, sealer primed the front clip, and put it all back together. Then I chopped out the rear wheel wells so they would actually be round and clear the tires. Its been a long day.
     

    Attached Files:

  8. AA/Fuel34fordpu
    Joined: Mar 15, 2005
    Posts: 1,266

    AA/Fuel34fordpu
    Member

    WOW that a looking nice :)
     
  9. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma

    I will finish the wiring tomorrow and get some pics out in the sun. Thanks to all the guys that helped. This wouldnt have been possible without you and the HAMB.

    Root Im going to make it to Mokan
     
  10. Roothawg
    Joined: Mar 14, 2001
    Posts: 25,960

    Roothawg
    Member

    Sweet. I'll be leaving here at 8:30-9:00ish Friday morning if you wanna caravan.
     
  11. Magnus
    Joined: Apr 30, 2006
    Posts: 904

    Magnus
    Member
    from Sweden

    SWEET. I love the colour, just like dad's?
     
  12. Rocco
    Joined: Jul 28, 2006
    Posts: 32

    Rocco
    Member

    thats one hot looking car already. Great choice of wheels.
     
  13. Hotrod F-1
    Joined: Dec 19, 2006
    Posts: 581

    Hotrod F-1
    Member
    from OK

    Looks great Pooch! Can't wait to see it on the streets (At the poker run next month ;)). :cool:
     
  14. rusty1
    Joined: Nov 25, 2004
    Posts: 13,034

    rusty1
    Member

    ...aint it great when a plan comes together?....better let your dad have the first drive! Nice 55.,...love them g***ers.
     
  15. Firecracker
    Joined: Aug 6, 2007
    Posts: 239

    Firecracker
    Member

    that looks like its comming along really good. I can't wait to see it when it's finished
     
  16. Gotgas
    Joined: Jul 22, 2004
    Posts: 7,250

    Gotgas
    Member
    from DFW USA

    "Sort of a cross 'tween piss yella and puke green."

    THAT is a great car!
     
  17. RUSTY50F1
    Joined: Jul 22, 2006
    Posts: 117

    RUSTY50F1
    Member

    That car looks great can't wait to get a close up look next month at the run.
     
  18. atomickustom
    Joined: Aug 30, 2005
    Posts: 3,407

    atomickustom
    Member

    Swwwweeeetttt!!!!
     
  19. OL 55
    Joined: Nov 4, 2005
    Posts: 14,824

    OL 55
    Member

    Very nice, get some video at the drags for us !!
     
  20. Hey I recognice that double nickle! : )

    Looking good. Good luck at the races
    We have to do that some day.
    Have a Fantaboulous weekend!

    Klaus
     
  21. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma

    We made it to the drags and had a blast. We got three good p***es. The best time was a 15.32. Then I learned a valuable lesson. Slicks are hard on parts. Ill admit it was my fault,dad said take it easy, but it was running so good. I didnt get my line lock installed before we left so I was doing rolling burnouts and during the third one she started bouncing. Dave told me after the run the rear end looked like it was moving around more than it should. We checked it out and everything looked fine so I hit the track one more time. The engine and trans slid back about an inch and when it did the clutch stuck to the floor on my 1-2 shift. I zinged the motor pretty good but I didnt blow it up. No serious damage but I was a little upset. The pedal came up at about the halfway mark and she started pulling in second so limped my way back to the pits and did somthing I havent done in a long time. I parked my car on the trailer and went to the stands and watched everyone else race. I sat there with Dad and Dan and we watched cheered and laughed untill the last car ran down the track and they told us to go home. It was cool to see all the people that I had met over the weekend run. I am usually in the line, on the track, at the trailer, or somewhere in between. I might spend a little time in the stands next year just to see some of the show. I will post some pics as soon as I get them ready.
    Pooch
     
  22. Magnus
    Joined: Apr 30, 2006
    Posts: 904

    Magnus
    Member
    from Sweden

    Man, that **** but I'm glad you made it. From the bottom of my heart I really have to try to get to the drags next year. Best of luck to you and give our best to your family.
     
  23. mortecai
    Joined: Mar 10, 2001
    Posts: 263

    mortecai
    Member

    Wow Can't wait till she is finished. what a great project
     
  24. Wow that ****s! At least you can say you had fun doing it.
    HAMB drags Hmmmm. next year Hmmmm. Something to think about!
    Best wishes to you! Don't worry you'll have her back on the roads again soon!

    See ya

    Klaus
     
  25. Hotrod F-1
    Joined: Dec 19, 2006
    Posts: 581

    Hotrod F-1
    Member
    from OK

    Breaking stuff is never that fun, but it makes for great stories to tell. :D I'm ready to go to the drags now. Come on next year. Now hurry up and get that car fixed, I've got a truck waiting on you. :D Good luck with it. :cool:
     
  26. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma

    I just finished going through my pics and I only have two pics of my car.
    Pooch
     

    Attached Files:

  27. atomickustom
    Joined: Aug 30, 2005
    Posts: 3,407

    atomickustom
    Member

    The car is awesome no matter what it runs! Next year it'll be scorching our eyes and scorching the track. Just remember the traction bars. (Maybe now we know why so many g***er chevies ran ladder bars?)
    It was great to see all of you again. We gotta start doing this more than once a year. Anything in the Spring in your area?
     
  28. gavin
    Joined: Dec 6, 2005
    Posts: 94

    gavin
    Member
    from Sonoma

    I haven's seen the trick of using 2 engine stands as a rotisserie, very cool. I am in the middle of a bunch of frame welding, that is going to come in handy.
     
  29. Whitey
    Joined: May 11, 2005
    Posts: 242

    Whitey
    Member
    from T-Town

    Great build up photos pooch!

    It was great meeting you this weekend!!!

    I'm comin down to Yukon soon!!!
     
  30. Pooch
    Joined: Apr 11, 2006
    Posts: 869

    Pooch
    Member
    from Oklahoma


    Come on down Friday nights are always good. We usually have something going on. If you come down on the 29th you could catch our last poker run of the year.
    Pooch
     

Share This Page

Register now to get rid of these ads!

Archive

Copyright © 1995-2021 The Jalopy Journal: Steal our stuff, we'll kick your teeth in. Terms of Service. Privacy Policy.

Atomic Industry
Forum software by XenForo™ ©2010-2014 XenForo Ltd.